Yahia Workshops
صندوق أدوات المهندس — مجاني

Built-up Section Properties — I · T · Box

احسب خواص أي قطاع مُلحَّم من ألواح في ثانية: A والوزن kg/m، Iy و Iz، iy و iz، Wel و Wpl، It و Iw، الـ Shear centre و Av — ومعاهم Class القطاع حسب الـ Grade.

  • EN 1993-1-1:2005 Table 5.2
  • EN 1993-1-5:2006 §4.4
  • EN 10025-2:2004

الأداة بتساعدك — المهندس المسؤول هو اللي بيراجع ويعتمد.

PNAG
To scale · G = centroid = shear centre · PNA = plastic neutral axis
  • Area A110.8cm²
  • Mass87.0kg/m
  • Iy46,037cm⁴
  • Iz2,137cm⁴
  • Wpl,y2,096cm³
  • It70.21cm⁴
  • Class (S355)Compression 4 · Bending y 1

Section properties

Geometry

Area A110.8cm²
Mass per metre86.98kg/m
Centroid from the bottom zG250.0mm
Plastic axis from the bottom zpl250.0mm
Shear centre from the bottom zS250.0mm

Major axis y-y

Iy46,037cm⁴
iy20.38cm
Wel,y (top fibre)1,841cm³
Wel,y (bottom fibre)1,841cm³
Wpl,y2,096cm³

Minor axis z-z

Iz2,137cm⁴
iz4.39cm
Wel,z213.7cm³
Wpl,z331.7cm³

Torsion & warping

Torsion constant It70.21cm⁴
Warping constant Iw1,249,365cm⁶

Shear & fire

Shear area Av,z (load ∥ web)46.80cm²
Shear area Av,y (load ∥ flanges)64.00cm²
Painting surface (outer)1.780m²/m
Section factor Am/V, all sides1611/m
Am/V, box protection1261/m

Yield strength (EN 10025-2)

fy, top flange (t 16 mm)355N/mm²
fy, web (t 10 mm)355N/mm²

Cross-section class — EN 1993-1-1 Table 5.2

Pure compression → Class 4

  • Top flange outstands (outstand, ε 0.814)c/t = 5.9 · limits 7.3 / 8.1 / 11.41
  • Bottom flange outstands (outstand, ε 0.814)c/t = 5.9 · limits 7.3 / 8.1 / 11.41
  • Web (internal, ε 0.814)c/t = 46.8 · limits 26.8 / 30.9 / 34.24

Major-axis bending (top flange in compression) → Class 1

  • Top flange outstands (outstand, ε 0.814)c/t = 5.9 · limits 7.3 / 8.1 / 11.41
  • Web (internal, ε 0.814)c/t = 46.8 · limits 58.6 / 67.5 / 100.91

Major-axis bending, top flange in compression. Limits = Class 1 / 2 / 3.

Class 4 in compression → effective area Aeff = 100.2 cm² (90.4 % of A), EN 1993-1-5 §4.4 with ψ = 1.

ε = √(235/fy) of each plate from its own thickness (EN 10025-2). c measured without the welds (on the safe side).

Check this section to EN 1993-1-1 — resistance, buckling, LTB and the interactionSteel Member Design →
How it is calculated
  • Plates as rectangles, welds and root radii ignored. y-y = major axis, z-z = axis of symmetry; z measured from the bottom.
  • Wpl about the equal-area (plastic) axis; Wel,y = the smaller of Iy / distance to the top and to the bottom fibre.
  • It: open sections Σ b·t³/3; box: Bredt 4·Am²/∮ds/t on the mid-thickness line; plate: solid rectangle.
  • Iw: I = If₁·If₂/(If₁ + If₂)·hs²; T = b³·tf³/144 + tw³·h′³/36; box ≈ 0 (closed). Shear centre of an I nearer the stiffer flange.
  • Av (EN 1993-1-1 §6.2.6(3)) with η = 1.0: welded I and box Σ hw·tw, T 0.9·(A − b·tf).
  • Am/V (EN 1993-1-2 §4.2.5): exposed on all sides — outer perimeter / A; box protection 2(b + h) / A. Mass with 7850 kg/m³.
  • The tool assists — the responsible engineer checks and approves.

اتعلم التصميم ده بالتفصيل

الأداة بتحسب. الكورس بيعلمك ليه وإزاي، على مشروع حقيقي.