Rebar & Lap Length — EN 1992
Bar areas and weights (n Ø or Ø @ s), bars for a required As, and anchorage and lap lengths to EN 1992-1-1 for every diameter at once.
- EN 1992-1-1:2004 §8.4
- EN 1992-1-1:2004 §8.7
- Table 3.1
The tool assists — the responsible engineer checks and approves.
Bar area & weight
- As804mm²
- As8.04cm²
- Mass6.31kg/m
- Bars4
Anchorage & lap length — EN 1992-1-1 §8.4, §8.7
Straight bars, recommended values (γc 1.5, γs 1.15, αct 1.0). Defaults are on the safe side.
Fig. 8.2: good when h ≤ 250 mm, or the bar is within 250 mm of the bottom (h ≤ 600 mm), or more than 300 mm below the top (h > 600 mm); otherwise poor (typically top bars of deep beams).
- Anchorage lbd, Ø16650mm
- lbd / Ø40.3Ø
- Lap l0, Ø16970mm
- l0 / Ø60.4Ø
- fctd = αct·fctk,0.05/γc = 1.0·1.8/1.5 = 1.20 N/mm² (EN 1992-1-1 §3.1.6(2), Table 3.1)
- η1 = 1.0 (good bond, §8.4.2(2)), η2 = 1.00 (Ø 16 ≤ 32 mm)
- fbd = 2.25·η1·η2·fctd = 2.70 N/mm² (eq. 8.2)
- σsd = 1.00·fyd = 1.00·500/1.15 = 434.8 N/mm²
- lb,rqd = (Ø/4)·(σsd/fbd) = (16/4)·(434.8/2.70) = 644 mm (eq. 8.3)
- α1 = α2 = α3 = α4 = α5 = 1.0 (straight bar, no reductions — on the safe side)
- lbd = α2·lb,rqd = 644 mm ≥ lb,min = max(0.3·lb,rqd, 10Ø, 100) = 193 mm → lbd = 644 mm (eq. 8.4, 8.6/8.7)
- α6 = (ρ1/25)^0.5 = (100/25)^0.5 → 1.500 (1.0 ≤ α6 ≤ 1.5, Table 8.3)
- l0 = α2·α6·lb,rqd = 966 mm ≥ l0,min = max(0.3·α6·lb,rqd, 15Ø, 200) = 290 mm → l0 = 966 mm (eq. 8.10, 8.11)
All diameters — same settings (rounded up to 10 mm)
| Ø | lb,rqd | lbd | l0 | l0 / Ø |
|---|---|---|---|---|
| 8 | 330 | 330 | 490 | 60 |
| 10 | 410 | 410 | 610 | 60 |
| 12 | 490 | 490 | 730 | 60 |
| 14 | 570 | 570 | 850 | 60 |
| 16 | 650 | 650 | 970 | 60 |
| 18 | 730 | 730 | 1,090 | 60 |
| 20 | 810 | 810 | 1,210 | 60 |
| 22 | 890 | 890 | 1,330 | 60 |
| 25 | 1,010 | 1,010 | 1,510 | 60 |
| 28 | 1,130 | 1,130 | 1,700 | 60 |
| 32 | 1,290 | 1,290 | 1,940 | 60 |
| 36 | 1,510 | 1,510 | 2,270 | 63 |
| 40 | 1,760 | 1,760 | 2,630 | 66 |
Not included: hooks/bends (α1), confinement by transverse bars (α3, α4) and transverse pressure (α5) — all taken as 1.0, which only adds length. Laps also need the transverse reinforcement of §8.7.4. The tool assists — the responsible engineer checks and approves.
Bar table — area and mass
| Ø mm | mm² | kg/m | 2 bars mm² | 4 bars mm² | @150 mm²/m |
|---|---|---|---|---|---|
| 6 | 28.3 | 0.222 | 57 | 113 | 188 |
| 8 | 50.3 | 0.395 | 101 | 201 | 335 |
| 10 | 78.5 | 0.617 | 157 | 314 | 524 |
| 12 | 113.1 | 0.888 | 226 | 452 | 754 |
| 14 | 153.9 | 1.208 | 308 | 616 | 1,026 |
| 16 | 201.1 | 1.578 | 402 | 804 | 1,340 |
| 18 | 254.5 | 1.998 | 509 | 1,018 | 1,696 |
| 20 | 314.2 | 2.466 | 628 | 1,257 | 2,094 |
| 22 | 380.1 | 2.984 | 760 | 1,521 | 2,534 |
| 25 | 490.9 | 3.853 | 982 | 1,963 | 3,272 |
| 28 | 615.8 | 4.834 | 1,232 | 2,463 | 4,105 |
| 32 | 804.2 | 6.313 | 1,608 | 3,217 | 5,362 |
| 36 | 1,017.9 | 7.990 | 2,036 | 4,072 | 6,786 |
| 40 | 1,256.6 | 9.865 | 2,513 | 5,027 | 8,378 |
Area πز/4 · mass with 7850 kg/m³.