Engineering Tools
Tools that give you an answer you can work with: the required dimensions, every check with its clause, and a PDF calculation note to submit. The calculation runs on our server, not in your browser.
The tool assists — the responsible engineer checks and approves.
Engineer's Toolbox — free
Simple everyday tools, free and open with no sign-in: instant results on your phone while you design.
- ToolFree
Concrete Cover — EN 1992
Nominal cover from the exposure class, step by step with the references: structural class (Table 4.3N), cmin,dur (Table 4.4N), cmin,b, Δcdev, casting against the ground and abrasion — with the indicative strength class of Annex E.
- X0 to XS3 with a description of each exposure class
- Every step with its clause and table
- cnom for every exposure class at once
- EN 1992-1-1:2004 §4.4.1
- Table 4.3N
- Table 4.4N
- Annex E
Open the tool → - ToolFree
Beam Formulas — M · V · δ
Single-span beam — simply supported, cantilever, fixed–fixed or propped — with a UDL and point loads: reactions, maximum M, V and deflection with their positions, and the diagrams.
- Four support cases, a UDL + up to 2 point loads
- Reactions and end moments, M+, M− and V with positions
- Deflection, L/δ and the stress M/W, with V, M and δ diagrams
Open the tool → - ToolFree
Rebar & Lap Length — EN 1992
Bar areas and weights (n Ø or Ø @ s), bars for a required As, and anchorage and lap lengths to EN 1992-1-1 for every diameter at once.
- As in mm² and cm², mass in kg/m or kg/m²
- Required As → number of bars or spacing for each diameter
- lbd and l0 in mm and in Ø, with the steps and clauses
- EN 1992-1-1:2004 §8.4
- EN 1992-1-1:2004 §8.7
- Table 3.1
Open the tool → - ToolFree
Built-up Section Properties — I · T · Box
Properties of any welded plate section in a second: A and mass per metre, Iy, Iz, iy, iz, Wel, Wpl, It, Iw, the shear centre and Av — with the section class for the grade.
- Symmetric or mono-symmetric I, T, two-web box, or a plate
- Class in compression and bending, and Aeff for Class 4
- Painting surface m²/m and the fire section factor Am/V
- EN 1993-1-1:2005 Table 5.2
- EN 1993-1-5:2006 §4.4
- EN 10025-2:2004
Open the tool →
Temporary Works & Methods tools
Built on the engines I use on real projects: enter your project data, get the answer and a calculation note.
- ToolLive
Crane / Piling Working Platform
Get the required working-platform thickness for a crane or piling rig, with a full calculation note to TWf2019:02, BR 470 and EN 1997-1.
- Required platform thickness
- Bearing checks for the platform and the subgrade
- PDF calculation note with your project header
- TWf2019:02
- BRE BR 470
- BS EN 1997-1
Open the tool → - ToolLive
Façade Tube & Fitting Scaffold
Design a façade tube & fitting scaffold — standards, ledgers, ties and couplers — with a clause-referenced calculation note.
- Checks for standards, ledgers and transoms
- Tie and coupler forces from wind and vertical loads
- PDF calculation note with your project header
- BS EN 12811-1
- EN 1993-1-1
- EN 74-1
- EN 1991-1-4
Design by first principles — not a TG20:13 compliance sheet.
Open the tool → - ToolComing soon
Lifting & Crane Selection
Crane selection, bearing pressure, rigging and the lifting plan — in one tool.
- Crane selection
- Outrigger bearing pressure
- A ready lifting plan
Details →
Eurocode tools
Design tools to the Eurocodes with clause references and a calculation note, by code.
Reinforced Concrete Structures
EN 1992 · Eurocode 2Coming soonComing soon — tools for this code are in preparation.
Timber Structures
EN 1995 · Eurocode 5Coming soonComing soon — tools for this code are in preparation.
Aluminium Structures
EN 1999 · Eurocode 9Coming soonComing soon — tools for this code are in preparation.